News

How To Choose A Granulator

Aug 09, 2022 Leave a message

_20221020113445

The choice of pelletizer depends on the material to be cut and its size, shape and thickness. The amount of material that needs to be pelletized and what to do with the recycled material are also key considerations. An operator safety assessment must be performed on the feed hopper. It should be sized to accommodate the largest particles without the need for labor-intensive and potentially dangerous pre-cutting. Most safety devices in pellet mills today involve electrical interlocks that prevent access to the cutting chamber until the rotor stops turning. Older pelletizers may not have these built-in protections.


Cutting room design

There are three basic cutting chamber designs: tangential, regular and straight drop, and hybrid models. The popular tangent design positions the rotor offset from the feed port in order to direct the stock into the downward cut of the rotating knives tangent to the cutting circle. The cutting chamber offers a large "bite" radius, which is the most efficient way to achieve high throughput and clean large, thin-walled parts.

granulator cutting chambers

The straight drop design feeds perpendicular to the cutting circle and is recommended for thick-walled parts. Its "bite" bite is unlikely to take up too much material, and it might stop the rotor from spinning. Hybrid models present material to the tool at an angle in between and allow custom molders with a wide range of part sizes and shapes to machine thick and thin wall materials on the same machine.

 

Rotorsplastics granulator rotor

The four main types of rotors are open, closed or solid, staggered and staggered/segmented. Open rotors provide unrestricted airflow through the cutting chamber, so they are more commonly used for pelletizing heat-sensitive resins or still warm stock processing. Enclosed or solid rotors have no open space between the rotating cutter and the center of the shaft, providing a stronger cutter mounting arrangement and increased inertia for cutting the thickest stock, such as large cold blows. Staggered rotors are available in closed or semi-closed configurations, ideal for cutting the heaviest thick-walled parts. In heavy-duty applications, flywheel pulleys increase rotor inertia and are often a more practical, cost-effective way to achieve greater cutting forces without increasing horsepower. Staggered/segmented rotors are typically offered in helical form, providing more cuts per revolution than traditional rotor designs. The cut circle remains the same after sharpening, minimizing screen clogging, heat build-up and fines. This configuration is ideal for cutting the heaviest thick-walled parts.



Knife

The number of blades, their arrangement, tip angle, speed and sharpness all have a significant impact on pelletizing quality and pelletizer efficiency. The tool can be mounted on a fixed bed or rotor. The clearance between the rotary knife and the bedknife is critical for downsizing performance. Smaller gaps result in cleaner, more efficient cuts and are important when grinding softer, more ductile polymers.



Plastic granulator knife

Many pelletizer designs offer only two stationary or bed knives. Check with the pelletizer manufacturer for proper knife clearance recommendations based on the material to be pelletized. Increasing the number of blades on the bed or rotor can significantly increase production by increasing the number of cuts per revolution. The "angled knife" arrangement that produces a scissor-like cutting action provides higher output, less horsepower, less noise, and less fines and dust than traditional straight-cut knives.


Low corners have a blunter tip for more brittle materials. High angle with sharp edge for cutting softer, energy absorbing materials. The lower tip speed increases the yield of uniform particles, reduces noise and reduces wear on the knife and cutting chamber. With high-speed rotors, particles are more likely to be carried around the machine or worn down into fine particles by repeated cuts. The slower rotor speed prevents this from happening by giving each particle a greater chance of passing through the sieve.


The frequency of sharpening the knife will depend on the abrasiveness of the material (glass filled and reinforcing compounds are the worst on the knife), and the steel alloy composition of the blade. Knife steels are usually designed for toughness or wear resistance. For soft, non-abrasive materials, knives made from chrome vanadium steel (CVS) are tough and chip resistant, but wear faster than other tool steels. D2 steel is the most common choice for pelletizer knives, it is harder and more wear-resistant, but may be more prone to shattering, which can be a problem if foreign metal is present. A regular maintenance schedule should be established to check tool wear and sharpness. A sharp blade is important for producing high quality regrind with a minimum of fines.


 Screen

Granulating sieve

Screen size is highly dependent on material composition and machine size. Smaller mesh openings and thinner meshes will produce more uniform particle size and highest throughput when running at slower rotor speeds. At higher speeds, on the other hand, larger screen openings are required to achieve throughput and reduce fines, although they may increase the particle size range, especially for brittle materials. Reversible screens have a longer lifespan.


 generalize

The goal of the process environment is to produce the highest quality parts 100% of the time with 0% scrap and 0% scrap. This should be achieved using the fastest possible machine cycle times and minimal human contact. To maximize profitability, this should all be performed at the lowest cost of the processor. Unfortunately, not all processors are capable of this. Technology and experience lead to significant improvements in the design and proper implementation of the correct auxiliary equipment to match the process. Choosing the right auxiliary process equipment is the key to successful processing. By taking the time to properly select the right equipment to match your process, you will be able to maximize process efficiency and help achieve your business goals and expectations. Don't always look at the initial cost of equipment. In addition to fit, form, function and compatibility with your other equipment; look at the "value" that equipment can add to your process. Evaluate the productivity gains (both short and long term) that can be achieved by properly implementing this equipment in your process. With today's latest technology, you have the opportunity to match and integrate the right additives into your process. This game will optimize your operations and most importantly increase your bottom line.


Send Inquiry